英國優科(UK)進口波紋管式疏水閥的熱敏元件為注滿易揮發液體的波紋管,利用液體的易揮發性和波紋管伸縮性。當蒸汽管線升溫時,液體揮發成氣體體積膨脹并產生壓力推動著波紋管伸長,蒸汽管線降溫達到易揮發的液體從氣體轉變成液體時體積縮收,波紋管內沒有推動力,波紋管縮收。 Bellows seal trap The thermo-sensitive element of bellows seal traps is bellows filled with volatile liquid, which employs the volatility of the liquid and flexibility of the bellows. When temperature of the steam pipe goes up, the liquid volatilizes into gas, the size expands and produces pressure to impel bellows to stretch. In contrast, when temperature of the steam pipe goes down to the temperature for gas to turn into liquid, the size gets smaller and the bellows contract due to lack of impetus. 優點: 1、排水溫度可以調節在70~100度之間,使用方便。 2、能夠阻止高溫凝結水的排放,保持蒸汽管線的熱能。 3、連續排水,沒有噪音。 4、蒸汽壓力小波動不影響使用。 5、結構簡單,體積小,安裝方便、隨意。 6、通過增加波紋管直徑提高凝結水的排量。 7、具有良好的排空氣性能,不怕凍。 8、零泄漏,背壓率達到75%。 Merits 1.Convenient use due to adjustable water discharge temperature ranging from 70 to 100 degrees. 2.Capability to prevent discharge of high-temperature condensate so as to maintain heat energy of the steam pipe. 3.Continuous water discharge without noise. 4.Free from the effect of small fluctuation of steam pressure. 5.Simple structure, small size and easy installation. 6.Improvement of discharge capacity of condensate by increasing diameter of bellows. 7.Good air discharge performance with resistance to coldness. 8.Zero leakage and backpressure ratio up to 75%. 安裝、使用注意事項: 安裝前管路應用蒸汽吹除污物。箭頭所示方向與流向*。 疏水閥前熱力管應有1~2米不必保溫。應安裝在低于用汽設備凝結水排出點的地方。 該閥出廠前疏水溫度已調節在95℃左右,如果需要改變疏水溫度或排水量時,可打開防護帽,松開suo緊螺母,旋轉調節螺釘,順時針旋轉閥芯前進,疏水量減少,疏水溫度降低;逆時針旋轉,閥芯后退,疏水量增大,疏水溫度上升。調整后,就將鎖緊螺母擰緊。 要定期保養,清除過濾網前的污物,保證疏水閥正常工作。 Installation/attention for use Before the installment of pipeline, use the steam to blow off the pollutant. The arrow shows the direction consistent with the flow direction. Ahead of the trap, the thermal tube of 1~2 meters need no heat-preservation. Be installed at the position lower than the condensation water discharge point of the steam-using equipment. Before leaving the plant, the hydrophobic temperature of trap has been adjust around 95℃. If it is needed to change the hydrophobic temperature or the displacement, open the shielding bonnet, loosen the lock nut, revolve the adjusting screw revolve the valve core clockwise, the hydrophobic volume reduces and the hydrophobic temperature drops; revolve it counterclockwise, the valve core backlashes, the hydrophobic volume increases, and the hydrophobic temperature rises. After the adjustment ended, tighten the lock nut. It is needed to make the periodic maintenance and clear the pollutant before the filtration screen, so as to guarantee the trap work normally.
United Kingdom UK UK flow control valve is the field of Europe's major producers and suppliers, the company headquarters is located in Welsh, the company is committed to research and development of fluid control valves, fluid control equipment, production systems, in many countries, the production valve base. Users of their products related to petroleum, chemical, electric power, metallurgy, pharmaceutical, food, water treatment, municipal water supply and drainage, gas, paper making, electronic industry, building, mechanical equipment and other fields.The British UK valve's main products are: electric valve, pneumatic valve, high temperature and high pressure valve, ball valve, gate valve, butterfly valve, globe valve, check valve, regulating valve, electromagnetic valve, safety valve, needle valve, steam trap | drain valve, plug valves, diaphragm valves, duckbill valve, discharge valve, exhaust valve, breathing valve, filter, flame arrester, throttle valve, angle seat valve, balance valve, drain valve, mud valve, cut-off valve, relief valve, pipe clamp valve, plunger valve, foot valve, mirror, flange, hydraulic control valves, and other series products. Welcome to purchase imported valve valve import brand \ / British / the British UK valve.